Search found 1256 matches
- 23 May 2024 15:57
- Forum: Tre e mezzo
- Topic: Strada carbs
- Replies: 6
- Views: 57
Re: Strada carbs
400 four is a nice bike
- 23 May 2024 04:52
- Forum: Tre e mezzo
- Topic: Strada carbs
- Replies: 6
- Views: 57
Re: Strada carbs
With the floatbowl removed and a suitable container under the carb, manually lifting the float with a fuel tap on then slowly lowering should determine if the needle is sealing and give some indication of float height. It can be that the float is hanging up on the float bowl. There may be a witness ...
- 21 May 2024 15:37
- Forum: Tre e mezzo
- Topic: Gear shaft oil seal
- Replies: 3
- Views: 56
Gear shaft oil seal
Has anyone actually replaced a weeping gear shaft seal in situ?
In an ideal world a fine pointy hook or fine self tapper /wood screw would go in and the seal would pull out.
Marshall’s luck dictates I damage the seal but cannot extract it.
In an ideal world a fine pointy hook or fine self tapper /wood screw would go in and the seal would pull out.
Marshall’s luck dictates I damage the seal but cannot extract it.
- 21 May 2024 14:59
- Forum: Bikes and bits for sale
- Topic: 1983 Sport FOR SALE
- Replies: 9
- Views: 171
Re: 1983 Sport FOR SALE
50K miles less than mine, which had a good blast today and now my back knows it.
- 20 May 2024 16:23
- Forum: The 500
- Topic: Stock Air Box questions
- Replies: 5
- Views: 170
Re: Stock Air Box questions
Mine has a sort of groove or channel worn or made to accommodate the cable routing. I have had no issue with this in 17 years, except for a nipple coming off at the twistgrip once when naturally I was at the bottom of a steep hill.
- 12 May 2024 18:37
- Forum: Tre e mezzo
- Topic: Strada MK5 Front Spindle washer
- Replies: 8
- Views: 233
Re: Strada MK5 Front Spindle washer
Thanks for reminding me.I’ll go back to sleep…..
- 12 May 2024 14:58
- Forum: Tre e mezzo
- Topic: Strada MK5 Front Spindle washer
- Replies: 8
- Views: 233
Re: Strada MK5 Front Spindle washer
This is interesting. I thought why not remove my twin disc front cast wheel and check. It has not been off for a good while. What do I find? No washer either. Spindle goes through rh fork into speedo drive then through shouldered spacer on other side of wheel before exiting the lh fork. There is a g...
- 08 May 2024 10:36
- Forum: Tre e mezzo
- Topic: Spark plugs
- Replies: 21
- Views: 20469
Re: Spark plugs
I spoke with NGK at the NEC show last Nov about fake plugs. The rep said the company actively tried to suppress ( oops!)
fake plugs but it is a never ending mission.
fake plugs but it is a never ending mission.
- 06 May 2024 05:55
- Forum: Tre e mezzo
- Topic: 350 not charging the battery
- Replies: 4
- Views: 234
Re: 350 not charging the battery
Have you a copy of the Blue book Morini manual? According to the section on testing for correct charge function, you should be getting around 8amp with the meter connected in series to the red lead which goes from the generator to the battery at 6000rpm. Disconnect the three leads, 2 yellow and one ...
- 26 Apr 2024 14:49
- Forum: Tre e mezzo
- Topic: new to morini
- Replies: 18
- Views: 963
Re: new to morini
I have a slightly later 350, a K1 and that has the oil light, indicator light ( mine have worked faultlessly), lights on and high beam lights. The oil light comes on very rarely when running indicating that the sender has some muck in or needs replacing. I got a few in case from ebay and of course i...
- 15 Apr 2024 14:47
- Forum: Factory customs
- Topic: Excalibur jetting
- Replies: 5
- Views: 1680
Re: Excalibur jetting
I marked the twistgrip with a series of different colour paint lines to help me, 1/8 ,1/4,1/2 . Above about half I was not concerned about as it was up to half that affecting my steady throttle response. Both on the 350 and the 507 I have experimented with the idle jets sizes from 50 through to 43. ...
- 14 Apr 2024 19:19
- Forum: Factory customs
- Topic: Excalibur jetting
- Replies: 5
- Views: 1680
Re: Excalibur jetting
Go back to the front page of this website and about halfway down is a link to the Morini club.nl pages. In Technical/carburettors is a table of settings. This might be of help. My experience with the air box housing is the opposite of the oft suggested benefit of removing the flowerpot etc.Also with...
- 18 Mar 2024 19:55
- Forum: The 500
- Topic: Rear Master Cylinder
- Replies: 10
- Views: 1196
Re: Rear Master Cylinder
That is really good news and I am sure others will be interested in this.
- 17 Mar 2024 20:04
- Forum: Off road bikes
- Topic: Oil Capacity 501 Camel
- Replies: 1
- Views: 2045
Re: Oil Capacity 501 Camel
I use 2.5L in both my 350 and my 507.
- 13 Mar 2024 18:16
- Forum: The 500
- Topic: Rear Master Cylinder
- Replies: 10
- Views: 1196
Re: Rear Master Cylinder
If you go with the Gemini Karts option do let us know how you get on. It looks promising.