Mike,
I have a 240Mph speedo when changing from MPH to KPH on the 1200, as I guess you did on the Milano, can the factory change it, apparently not.
I vote for marking it up or add a GPS speedo or use a phone.
Mark
Search found 670 matches
- 06 May 2024 12:21
- Forum: 250 Vee
- Topic: Speedo converter
- Replies: 3
- Views: 120
- 06 May 2024 11:57
- Forum: Tre e mezzo
- Topic: 350 not charging the battery
- Replies: 4
- Views: 187
Re: 350 not charging the battery
Red to battery+ amps = no response at the multimeter. Yellow to Yellow 2.1v Yellow 1 to red 4.5v Yellow 2 to red 2.5v White to earth 0.04ohm Yellow to Yellow resistance 0.90 mili ohms. Yellow1+2 to red nil resistance response. Again thanks for your help- Layton Hi Layton welcome to the mysterious w...
- 09 Apr 2024 17:31
- Forum: Bikes and bits wanted
- Topic: atomiser/emulsion tube.
- Replies: 9
- Views: 1262
Re: atomiser/emulsion tube.
According to the article in La Strega the U has 0.8mm holes.
The CT has holes of 1.0mm at A and B
If adapting other tubes excess holes can be plugged with solder.
Mark
The CT has holes of 1.0mm at A and B
If adapting other tubes excess holes can be plugged with solder.
Mark
- 09 Apr 2024 17:15
- Forum: Bikes and bits wanted
- Topic: atomiser/emulsion tube.
- Replies: 9
- Views: 1262
Re: atomiser/emulsion tube.
You can get an available spec 260 then drill out 0.8 mm holes, then ream with a 2.60 reamer to make a U pattern. John this is a useful table but it omits a little detail, not all holes are 0.8mm across all emulsifiers. For example BR has 1.0mm holes. So we would need to double check the U hole size...
- 06 Mar 2024 21:06
- Forum: 250 Vee
- Topic: 250 rebuild from bits
- Replies: 34
- Views: 9695
Re: 250 rebuild from bits
Hi, Glad to hear it runs. Brand new bore and/or rings will take some time to bed in and give good compression. Mark: can you explain why the ignition needs retarding if the transducers don't give enough advance at 6000? I would have thought to advance them. Scooters advance earlier - the controlling...
- 29 Feb 2024 23:42
- Forum: 250 Vee
- Topic: 250 rebuild from bits
- Replies: 34
- Views: 9695
Re: 250 rebuild from bits
Hi Hopefully it will be a runner soon. Probably you already considered these points, but in case there was something missed. Tried a 500 airfilter and it does not fit for me! It, if its a genuine 500 filter, will need to be filed a little to clear the posts or it wont sit properly, but it will fit. ...
- 10 Feb 2024 13:12
- Forum: 250 Vee
- Topic: Ignition timing issues
- Replies: 14
- Views: 4111
Re: Ignition timing issues
Hi Barry . I noticed that you sent for tranducer's from Italy, did you finally get your items or refund as I'm thinking along your lines for replacing my ignition. But don't want to lose my hard earned cash in not receiving either ., if not where did you get your parts ...Dave Dave, You should have...
- 18 Jan 2024 13:11
- Forum: 250 Vee
- Topic: 250 2C tyres
- Replies: 4
- Views: 1300
Re: 250 2C tyres
Hi Parky, Good to hear of another 250 I agree with 72degrees 100% ME22s all the way, don't read reviews, ask people who ride them, you can go 3.25 on the rear but not 3.50 We have owned 250s since 93. I also have a 250 2C with Avon roadriders, too big especially the front... stay with the Metzelers....
- 18 Jan 2024 13:04
- Forum: Tre e mezzo
- Topic: Fuel tap overhaul
- Replies: 10
- Views: 2114
Re: Fuel tap overhaul
Long story short, remove the electric one, plugged the hole and use the right rear position only with a std fueltap with two positions. Regards A Good advice! But I do this, leave the tap in place and put a length of 8mm bar inside the fuel pipe to stop it because mine would not seal off. Then use ...
- 12 Jan 2024 12:19
- Forum: 250 Vee
- Topic: Supercharged Morini will get a 250J
- Replies: 3
- Views: 1285
Re: Supercharged Morini will get a 250J
interesting project Robert and Miss Amy. How strict is the 250cc class, there is a lot of meat on those liners :wink: And thanks to Morini modularity - a lot from other capacity machines is interchangeable. The torque settings for the 250 2C need to come from the 250 2C user manual and not from the ...
- 02 Dec 2023 09:34
- Forum: Bikes and bits wanted
- Topic: 250 2c front wheel washer/seal
- Replies: 5
- Views: 3910
Re: 250 2c front wheel washer/seal
Yep, no problem part 16 not required with ready shielded bearings.Parker3865 wrote: ↑01 Dec 2023 17:10 Have fitted shielded bearings thanks. So you reckon all will be ok? Many thanks
Cheers Mark
- 01 Dec 2023 16:15
- Forum: Bikes and bits wanted
- Topic: 250 2c front wheel washer/seal
- Replies: 5
- Views: 3910
Re: 250 2c front wheel washer/seal
Hi, The part 16 43.05.49 is just a shield for the usually fitted unshielded bearing, if you fit new metal shielded bearing then its not needed, notice the other bearing is described in Italiano as schermato this means shielded. If you already have fitted an unshielded bearing then its best to fit a ...
- 01 Dec 2023 13:49
- Forum: 250 Vee
- Topic: Cam belt size
- Replies: 8
- Views: 6605
Re: Cam belt size
Dave, If you have a B pinion, you may have to try another supplier if the generic belt from Conti is too slack. Its likely that you got a generic belt on the long end of the distribution of lengths. Usually we buy a few generic belts and select the best fit as they are pretty cheap different people ...
- 21 Nov 2023 15:17
- Forum: The 500
- Topic: clutch spring nuts seized
- Replies: 20
- Views: 6908
Re: clutch spring nuts seized
Here are the SURFLEX kit part numbers with MM parts in brackets, you can check with vendor Full set: S 1149 Serie composta da: 5 articolo 2 M 77 (20.01.25) 1 articolo 62 M 39 (20.01.24) 4 articolo 62 M 43 (20.01.26) 1 articolo 2 M 131 (20.01.32) driving plate set (fibre composites) S 1149/B Serie co...
- 21 Nov 2023 15:05
- Forum: The 500
- Topic: clutch spring nuts seized
- Replies: 20
- Views: 6908
Re: clutch spring nuts seized
bad luck Terry although if it was turning it may have been of limited use returning to my query about clutch plates - these are advertised on fleabay but the 500 sport is pretty much the only one not listed. Just to be on the safe side - can I be certain they will fit? https://www.ebay.co.uk/itm/26...