Search found 18 matches
- 23 Jun 2023 14:29
- Forum: The 500
- Topic: More Carburettor Woes! Help1
- Replies: 10
- Views: 8446
Re: More Carburettor Woes! Help1
Steve Brown: a very delayed reply. Thanks for your help, very useful indeed. I threw the choke cable away (seals were utterly knackered - good shout), and took the choke lever off it now has the carb chokes on each carb. I stripped and sonic cleaned the carbs, and due to previous poorly repaired dam...
- 23 Jun 2023 14:12
- Forum: The 500
- Topic: Speedometer Cable '81 500SEI
- Replies: 5
- Views: 3315
Re: Speedometer Cable '81 500SEI
Stempy: I just had a good chat with Dave at JJCables, I am going to send him my cable that he is going to take the upper ferrule off that and graft it onto a new cable for me, £23!! get in! Apparently, they'll do their best to make any cable for any bike! But they can't get bent Italian ferrules :) ...
- 22 Jun 2023 14:24
- Forum: The 500
- Topic: Speedometer Cable '81 500SEI
- Replies: 5
- Views: 3315
Speedometer Cable '81 500SEI
Hello folks. Went for the shakedown run on the 500 to the Bell yesterday, with George. It was good to meet up with all of you by the way. The one proper failure that I did have on the way back, was the speedometer cable. It's gone to speedo' cable heaven. The one on the Mdina Italia site does not ap...
- 13 Jun 2021 12:28
- Forum: The 500
- Topic: More Carburettor Woes! Help1
- Replies: 10
- Views: 8446
Re: More Carburettor Woes! Help1
Thanks for the replies chaps, very helpful. To be honest Dave, I had presumed that the front tap was a small electrical fuel pump/fuel tap. I have just found a thread posted on the board about replacing this tap with an MZ ETZ manual tap. Does anyone know what other, if any, manual fuel taps can be ...
- 10 Jun 2021 17:09
- Forum: Bikes and bits for sale
- Topic: Priceless Unobtainium Unearthed!
- Replies: 16
- Views: 8632
Re: Priceless Unobtainium Unearthed!
Here's a thing chaps, what happens if you need one, but there aren't any? What alternatives are there?
J
J
- 10 Jun 2021 16:33
- Forum: The 500
- Topic: More Carburettor Woes! Help1
- Replies: 10
- Views: 8446
More Carburettor Woes! Help1
I have a problem with my SEI, it will accelerate so far and the it just goes "bwarrrrrr" and bogs down, before eventually clearing. It never seems to run clean from then on though, it feels restricted. The bike is equipped with Dellorto PHBH26 BS carburettors. The main jet is 120: the idel...
- 21 May 2020 16:24
- Forum: Bikes and bits wanted
- Topic: Hydraulic Brake Set 42.08.20 - fork damper 35mm Marz
- Replies: 0
- Views: 1738
Hydraulic Brake Set 42.08.20 - fork damper 35mm Marz
Has anyone any idea where I could get hold of a couple of new nylon fork bushese for this item (35mm Marzzochi's), or indeed any spares for these forks? The bushes are serviceable, but whilst the forks are apart having new fork seals and a service I thought I might try to improve matters! Any (sensi...
- 21 May 2020 16:21
- Forum: The 500
- Topic: 42.08.20 Hydraulic Brake Set, or fork damper...
- Replies: 5
- Views: 4088
Re: 42.08.20 Hydraulic Brake Set, or fork damper...
Thanks Mark. I just had a look they do not appear to have the bits, however my Italian is not great!!
- 21 May 2020 16:17
- Forum: Bikes and bits wanted
- Topic: Hydraulic Brake Set 42.08.20 - fork damper 35mm Marz
- Replies: 0
- Views: 1699
Hydraulic Brake Set 42.08.20 - fork damper 35mm Marz
Has anyone any idea where I could get hold of a couple of new nylon fork bushese for this item (35mm Marzzochi's), or indeed any spares for these forks? The bushes are serviceable, but whilst the forks are apart having new fork seals and a service I thought I might try to improve matters! Any (sensi...
- 21 May 2020 16:02
- Forum: The 500
- Topic: 42.08.20 Hydraulic Brake Set, or fork damper...
- Replies: 5
- Views: 4088
42.08.20 Hydraulic Brake Set, or fork damper...
Has anyone any idea where I could get hold of a couple of new nylon fork bushese for this item (35mm Marzzochi's), or indeed any spares for these forks? The bushes are serviceable, but whilst the forks are apart having new fork seals and a service I thought I might try to improve matters! Any (sensi...
- 20 Apr 2020 15:05
- Forum: Bikes and bits for sale
- Topic: 3D printed Speedo MPH Bezel
- Replies: 0
- Views: 1989
3D printed Speedo MPH Bezel
Folks: if anyone is interested my son has just printed me an mph bezel on his 3d printer. It doesn't look half bad, quite smart. Unfortunately I cannot upload an image, because my "...board attachment quota...", has been reached, apparently! However message me and I'll send you a picture o...
- 18 Mar 2020 18:10
- Forum: Bikes and bits for sale
- Topic: Flywheel puller
- Replies: 26
- Views: 12277
Re: Flywheel puller
Mike - found the user control panel and messages etc., but I don't have one from you.
Thanks
Jack
Thanks
Jack
- 18 Mar 2020 18:06
- Forum: Bikes and bits for sale
- Topic: Flywheel puller
- Replies: 26
- Views: 12277
Re: Flywheel puller
Mike,
can you please tell me where I might find it, I genuinely do not have a clue!
Thanks
Jack
can you please tell me where I might find it, I genuinely do not have a clue!
Thanks
Jack
- 17 Mar 2020 17:43
- Forum: Bikes and bits for sale
- Topic: 500 SEI centre-stand
- Replies: 1
- Views: 2178
Re: 500 SEI centre-stand
Folks - I've sorted the centre-stand thanks.
Jack
Jack
- 17 Mar 2020 17:38
- Forum: Bikes and bits for sale
- Topic: Flywheel puller
- Replies: 26
- Views: 12277
Re: Flywheel puller
Hello MIckey.
It was me who needed one. Perfectly reasonable price. I'll take it off your hands.
Bank transfer? I don't know if you can send me a private message through the site.
If not we'll need to sort something out.
Cheers
Jack
It was me who needed one. Perfectly reasonable price. I'll take it off your hands.
Bank transfer? I don't know if you can send me a private message through the site.
If not we'll need to sort something out.
Cheers
Jack