alternative fork oil seals

250 2c- the Wee-WeeVees

alternative fork oil seals

Postby morini250 » 19 Jun 2018 19:30

Hello, I already posted in parts wanted for the originals, but would it be possible to use fork seals of another bike where parts are easier to come by? I'd be very grateful for any hints!
morini250
 
Posts: 2
Joined: 18 Jun 2018 16:55

Re: alternative fork oil seals

Postby Ming » 20 Jun 2018 06:59

Any seal will do. Measure the inner diameter (fork diameter) and the outer diameter (where it sits in the stanchion) and search for that size oil seal. When you come to fit them, use a suitable drift to push them in, such as a similar sized socket or the old seal, then lubricate the lips before inserting the fork legs.
User avatar
Ming
 
Posts: 300
Joined: 01 Aug 2014 16:32
Location: Central France

Re: alternative fork oil seals

Postby Ming » 20 Jun 2018 07:09

Try 32mm oil seal in ebay, there are plenty there.
User avatar
Ming
 
Posts: 300
Joined: 01 Aug 2014 16:32
Location: Central France

Re: alternative fork oil seals

Postby davel182 » 20 Jun 2018 17:26

I believe the 'official' size for the Paioli forks is 31.7x42x7/9 and these are/were available from Ariete / Athena, and NLM have/had part number A31.742X7/9 (not listed in the parts.pdf) for the 250 models. I think the Italian Subito site advertises part number 42.05.17 as size 32-42-7 but I'm guessing the 32 is just a rounded up number.
davel182
 
Posts: 37
Joined: 18 Feb 2016 12:01
Location: Wolverhampton

Re: alternative fork oil seals

Postby mbmm350s » 02 Jul 2018 11:54

I replaced the fork seals on a 250 2C using the parts from NLM last weekend, no problem. The parts are 31.7 x42x7/9 as mentioned previously. 31.7 mm surely that's 1 1/4 inches! Fork capacity is 160cc I am using 10W (castrol) from Halfords.
Mark
mbmm350s
 
Posts: 13
Joined: 22 Jun 2018 10:18
Location: Berkshire UK

Re: alternative fork oil seals

Postby jacks the lad » 08 Aug 2018 12:28

Having only just acquired a 2c and sorted the foot rests I took it for it's first decent ride over the weekend. Only to find upon my return the front fork seals were weeping (there was nothing in the paperwork that came with the bike to indicate that they had ever been changed, so they could well be 38 years old by now), therefore the above posts were of some interest.
Perhaps someone here can tell me, do I need any special tools in order to replace them? Other than a large allen key (12mm?) to take out the top fork nuts.
jacks the lad
 
Posts: 13
Joined: 18 Jul 2018 11:37

Re: alternative fork oil seals

Postby mbmm350s » 08 Aug 2018 13:45

Hi,
No special tools needed, though do take care when prising out the old seals as the slider walls are quite thin.
The seals, two per side, are held in by a snap ring which might be rather corroded.
I use a length of wooden dowel down the tube to hold the damper assembly whilst undoing the bolt in the bottom of the slider.
Seals available from NLM and I am using 10W fork oil 160cc per leg

Years ago I ground a half inch radiator tail key to be a snug fit, but you could probably buy a 12mm Allen Key for less....

Mark
mbmm350s
 
Posts: 13
Joined: 22 Jun 2018 10:18
Location: Berkshire UK


Return to 250 Vee

Who is online

Users browsing this forum: No registered users and 1 guest