Various Morini parts available

[Ming]

Feeling somewhat better, so I ventured into the barn and grabbed the first few bits to hand.

Morini bits.png (377.41 KiB) Viewed 2118 times

I have a plastic 350 heatshield - the mounting points need repair.
An unused 500 exhaust spanner.
Bearing support for a mechanical tacho.
A pair of Veglia Speedo & Tacho supports, without the rubber gaiters.
A white faced kmh Speedo in good condition.
A cable brake / clutch lever (early singles I think).
A Grimeca front master cylinder, probably in need of new seals.

Sorry the photo is a bit fuzzy, a bit like my vision!
Watch out for the next tranche.

[rossguzzi]

Hi,
I would be interested in the gauges support brackets. Could you email me at rbannister59@gmail.com
I am guessing the normal Sport rubbers would fit ?
Many thanks.
Ross

[ianlucas006]

Hello Ming / Ross
The clock supports are actually very early Strada ones. I am looking for a set! If you want Sport ones I probably have some as well as the rubber supports. Thanks Ian

[rossguzzi]

Hi Ian,
I am after a support like this for my sport so I can fit my strada top clamp.
Cheers

[Ming]

Here's another batch

More parts

IMG_2236.jpeg (393.1 KiB) Viewed 2011 times

So, a front hydraulic hose splitter mount.
A 350 battery base rubber.
A gear selector rose joint adaptor.
An iffy black transducer.
A set of pushrods from a Kanguro.
A pair of fork slider caps and cable guides.
A repaired stator mounting plate.
A pair of handlebar levers of unknown provenance.

PM me for an item and I'll set it aside.

[morini_tom]

I’m currently putting together a sectioned engine for the club so am on the lookout for certain parts, and damaged ones are ideal as it saves using bits which would otherwise keep a Morini mobile.

To this end the pickup and stator plate would be perfect please.

The pushrods and gear selector joint would be useful too if someone doesn’t have a greater need

Thanks,
Tom

[Ming]

A few more parts.

Sprockets&c.jpeg (12.56 KiB) Viewed 1512 times

A couple of 350 sprockets, 14 & 16 teeth, plus a 500 / 501 , a ratty exhaust nut, 2 sets of exhaust collets (350), lever end clutch adjuster.

Kickstart mech.jpeg (15.73 KiB) Viewed 1512 times

A 350 kickstart mechanism & primary gear

Head&tail.jpeg (13.4 KiB) Viewed 1512 times

Rectangular Bosch headlight & 350 CEV tail light.

[Ming]

And more:

Stand &c.jpeg (14.93 KiB) Viewed 1511 times

A 350 centre stand, a Kanguro kickstart, a lifting handle, a pair of pillion footrests, a pair of Kanguro footrests.

I know there are a couple of 350 rocker box covers, some Excalibur footrests and other odd bits, will look them out now it's a bit warmer.

[morini_tom]

The lifting handle will come in handy (if you forgive the pun) please

Thanks,
Tom

[Tim]

Interested in the cev rear light - will pm you direct

[Michel3007]

I would be interested in the 500 sprocket! I sent you a PM about it.

[Ming]

Pour Michel3007, je ne peux pas poster des photos par PM, donc:

P2020001.jpeg (52.14 KiB) Viewed 1367 times

P2020002.jpeg (48.43 KiB) Viewed 1367 times

Je crois c'est pour 500 / 501

[Ming]

Apologies - I described the speedo as being a white-faced one. I was mistaken (that went some time back). This is a black-faced speedo, with a nice chrome bezel, calibrated for km, km/h.

Speedo.jpeg (214.26 KiB) Viewed 1155 times

Might make your bike look even faster!