Atreyu, I dont have another coil(transducer) to try. I would think it unlikely they would both pack up together. The stator gives a reading of 300 ohms so looks OK. Which leaves the pickup. Not sure how to check it. I have only visually checked it to see if it turns on kicking.
Si
Search found 28 matches
- 20 Jun 2011 03:44
- Forum: Tre e mezzo
- Topic: No spark - No go
- Replies: 8
- Views: 6149
- 19 Jun 2011 22:04
- Forum: Tre e mezzo
- Topic: No spark - No go
- Replies: 8
- Views: 6149
Re: No spark - No go
Tried all the checks I could from the site, and a few ideas from Stewert at NLM. Still no sparks. It's going to have to have a trip to NLM when I get time.
Si
Si
- 15 Jun 2011 19:15
- Forum: Tre e mezzo
- Topic: No spark - No go
- Replies: 8
- Views: 6149
No spark - No go
Out for a run today when the bike suddenly cut out and would not start again, no spark on front plug couldn't get at the rear. Got home eventually with a bit of help from AA and my brother. Had a quck check and there is no spark at either plug. Can anyone give me some pointers of where to start look...
- 08 Jun 2011 08:20
- Forum: Site suggestions
- Topic: Forum problems
- Replies: 10
- Views: 24035
Re: Forum problems
My access seems to have improved this week, had no problems the last couple of days. The last couple of weeks had been awful. I was lucky if I had access 1 time in 10.
Si
Si
- 20 May 2011 06:49
- Forum: Tre e mezzo
- Topic: Banjo Bolt size
- Replies: 8
- Views: 5537
Re: Banjo Bolt size
Posting attempt 10.
Might be worth checking them all before ordering new lines. Not sure what size the calper is.
Si
Might be worth checking them all before ordering new lines. Not sure what size the calper is.
Si
- 17 May 2011 21:40
- Forum: Tre e mezzo
- Topic: Banjo Bolt size
- Replies: 8
- Views: 5537
Re: Banjo Bolt size
No worries Dave.
Some bikes do seem to have different size bolts in various places.I'll stick the other on E-bay some time. The first one I ordered never arrived so they sent me a replacemet. Otherwise I would have found out earlier.
Si
Some bikes do seem to have different size bolts in various places.I'll stick the other on E-bay some time. The first one I ordered never arrived so they sent me a replacemet. Otherwise I would have found out earlier.
Si
- 17 May 2011 10:50
- Forum: Tre e mezzo
- Topic: Banjo Bolt size
- Replies: 8
- Views: 5537
Re: Banjo Bolt size
An update on fitting a front brakelight switch to a '79 3 1/2. The M10 x 1.25mm switch I bought did not fit the Grimeca MC, must be a different thread to the banjo on the 500 yolk. Bought a M10 x 1.00 switch which fits great. All wired up to the same fusebox connections as the rear brale light and w...
- 15 May 2011 10:47
- Forum: Tre e mezzo
- Topic: Hi from new Forum member - 3 1/2 sport owner
- Replies: 3
- Views: 3340
Re: Hi from new Forum member - 3 1/2 sport owner
Welcome Tufftrax.
Only joined recently myself, also bought a bike from NLM about 4 weeks ago. Already changing a few bits, smaller indicators, front brakelight switch and stainless front mudguard. Still getting used to the right foot gearlever after years of jap stuff.
Enjoy your ride.
Si
Only joined recently myself, also bought a bike from NLM about 4 weeks ago. Already changing a few bits, smaller indicators, front brakelight switch and stainless front mudguard. Still getting used to the right foot gearlever after years of jap stuff.
Enjoy your ride.
Si
- 06 May 2011 10:08
- Forum: Club Products
- Topic: Replacement Side Panel Rubber Pins
- Replies: 35
- Views: 59449
Re: Replacement Side Panel Rubber Pins
Arrived this morning. Thanks Chris.
- 03 May 2011 11:47
- Forum: Club Products
- Topic: Replacement Side Panel Rubber Pins
- Replies: 35
- Views: 59449
Re: Replacement Side Panel Rubber Pins
Chris, sent you a cheque for 4 rubber panel pins about 3 weeks ago. Not heard anything and the cheque has not been cashed. Wondering if it reached you ok or just delayed with all the holidays recently.
Thanks
Si.
Thanks
Si.
- 03 May 2011 07:12
- Forum: Tre e mezzo
- Topic: Calipers
- Replies: 1
- Views: 2456
Re: Calipers
Thanks for the tip Simon
- 01 May 2011 18:47
- Forum: Tre e mezzo
- Topic: Banjo Bolt size
- Replies: 8
- Views: 5537
Re: Banjo Bolt size
Thanks Dave. It worked OK did it?
Si
Si
- 01 May 2011 16:04
- Forum: Tre e mezzo
- Topic: Banjo Bolt size
- Replies: 8
- Views: 5537
Banjo Bolt size
Could anyone tell me the size of the banjo bolt for the front master cylinder. Looking at getting a Banjo Bolt pressure switch fitted so the brake light will work off the front brake.
Thanks
Si
Thanks
Si